Blisters and Bubbles in Roof Waterproofing Membranes: Causes and Fixes
What exactly is a blister, and why does it matter?
Press a blister and you feel a raised, hollow patch: the membrane has lost its grip on whatever lies beneath it. The void may hold air, water vapour or some liquid water. In summer the pocket warms and swells under the sun, then contracts overnight, so the layer above it flexes up and down for months and years.
A blister is not automatically a leak. The membrane may still be intact across the top. But it is a weak spot. Someone steps on it and it bursts; repeated movement tears the membrane at the edge; and once there is a gap, rain finds the cavity underneath. That is why blisters are best read as an early warning, with the risk judged by their size, number and location.
The most common causes
| Cause | How the pocket forms | Clue to look for |
|---|---|---|
| Moisture trapped in the slab or screed | Sun heats the moisture into vapour that pushes the membrane up from below | Large blisters; dampness or water beneath when opened |
| Air in the pores of the concrete | Warming makes the air expand and escape through the still-soft coat | Many tiny blisters or pinholes in a liquid membrane |
| Dusty, weak or unprepared surface | Dust, laitance or a crumbly top layer stops bonding, so the coat lifts | Membrane peels up easily with powder underneath |
| No primer, or the wrong one | Only partial adhesion, leaving unbonded pockets | Scattered blisters with no clear pattern |
| Applied in strong sun or on a very hot surface | The top skins over quickly and traps solvent or water below | Taut skin over pockets, mostly on dark roofs |
| Coat too thick, or no wait between coats | The lower layer stays wet and traps the gas it gives off | Blisters where coats overlap or where material was heavily laid |
| Dew or rain before the coat has set | Water reaches the membrane before it has gained strength | Patchy, blotchy areas with small blisters |
| Weak laps or uneven torching in sheets | Air or water is left between layers because bonding is uneven | Long blisters or those near seams |
| Incompatible materials | A new coat reacts with, or seals in, an old one | Blisters after recoating an old system that was not assessed |
Often several causes act together: a slab not fully dry, coated on a hot afternoon with an unsuitable primer, can blister for three reasons at once. That is why diagnosis comes before any repair.
Does the type of membrane change what you see?
| System | Typical blister | Practical note |
|---|---|---|
| Liquid-applied (acrylic, polymer or polyurethane) | Small bubbles or pinholes, and sometimes a larger lift over moisture | Sensitive to surface prep, coat thickness and drying time; see the pros and cons of liquid membranes |
| Torch-applied bituminous sheets | Palm-sized swellings between layers or under a sheet | Usually partial bonding or trapped water, tied to workmanship at the torch |
| Self-adhesive sheets | Long air pockets | Appear where rolling pressure was too light or the surface was not primed |
| Spray foam with a protective coat | Coating lifting off the foam | Linked to moisture beneath the foam and to the top coat |
For a comparison of systems and their limits, see our guide to foam, rolls and liquid membranes.
How to size up a blister: is it serious?
You do not need instruments for a first impression. Go up at a safe time of day, then look and feel carefully:
- Size and number: one or two coin-sized blisters are a different matter from dozens in one patch.
- Feel under light pressure: a hollow, airy feel suggests air; a spongy feel or sloshing suggests water.
- Location: blisters near drains, laps, pipe outlets and edges matter more than one in a quiet field area.
- Condition of the surface above: look for hairline cracks, peeling or colour change around the edge.
- Foot traffic: a blister on a path people walk along will burst before long.
- Standing water: blisters where water ponds point to a slope problem as well; read about ponding water and slope.
- Signs indoors: a damp patch on the ceiling below means water is already getting through.
A simple moisture check before any repair
The key question before patching is whether the surface under the blister is damp. Patch over moisture and it will swell again. On bare concrete, or once a blister is opened, you can run a basic test:
- Choose a square of bare concrete of roughly one metre, visibly clean and dry.
- Tape a clear plastic sheet over it, sealing every edge.
- Leave it for at least a day, ideally taking in the sunny hours.
- Check it: droplets on the underside of the plastic, or darkening of the concrete, show moisture rising from below.
- Repeat in more than one place if the suspect area is large.
A concrete moisture meter may also be used, but its readings depend on the type of concrete and the product's instructions, so do not rely on a generic number. When in doubt, wait. Re-coating over damp concrete just repeats the failure.
- Keep away from unprotected edges, do not walk on wet or slippery surfaces, and avoid going up alone in strong heat. Dark roofs can burn hands and knees at midday.
- Bituminous sheets are often torched, which is a fire risk. Torch work should be done only by trained staff with an extinguisher to hand, away from flammable insulation and anything stored nearby.
- Primers, solvents and adhesives can be flammable and harmful to breathe. Read the product data sheet, ventilate, wear gloves and eye protection, and keep clear of flames and sparks.
- Watch for air-conditioning units, tanks and live cables on the roof. Never cut membrane near powered equipment.
- Do not cut open a sound membrane around a blister unless you know how it will be resealed the same day, especially if rain is possible.
Cut and patch, or remove and redo?
| Situation | Likely approach | Considerations |
|---|---|---|
| One or two small blisters, membrane intact, dry substrate | Cut, dry and patch locally | Compatible material, enough overlap, follow-up after the first summer |
| Scattered blisters with moisture beneath | Dry out and remove the area, then re-prepare and re-apply | Do not patch over damp; find where the moisture comes from |
| Widespread blistering or blisters that return after repair | Redo the affected area, or all of it | A problem in the base: moisture, preparation or unsuitable system |
| Blisters with cracking or water entering the building | Urgent inspection and a temporary fix, then decide | See repair or redo old roof waterproofing |
| Blisters at laps, edges or outlets | Rework the detail itself | Read about parapet and roof edge details |
Typical steps for a local patch
- Mark an area slightly larger than the blister and confirm dry weather with none forecast.
- Open it with a cross-shaped or small flap cut using a sharp blade, taking care not to score the concrete below.
- Lift the flaps, let any water out, dry the cavity and inspect both the underside of the membrane and the substrate.
- Remove loose or crumbling material, repair cracks and apply primer if the manufacturer calls for it.
- Re-bond the flaps with a material compatible with the membrane, or lay a patch that extends beyond the cut by the distance the supplier recommends.
- Seal the edges with the system's own sealing material and allow the stated curing time.
- Check the spot again after the first summer, or after a suitable flood test; see flood testing after waterproofing.
Liquid membranes are handled differently: the affected zone is usually scraped back to sound material, re-prepared and re-coated with the specified number of layers. For sheets, the damaged piece may be cut out and a new section laid with a proper lap. The principle is constant: if the cause is not dealt with, you cannot be sure the blister will not return.
Timing and heat in Jeddah and Makkah
Strong heat and coastal humidity make the timing of application a deciding factor. A dark concrete roof can run far hotter than the air above it, which makes the top of a liquid coat skin over and trap what has not yet evaporated. In Jeddah, dew can settle on cool surfaces in the early morning, so an early start on a damp roof can leave moisture beneath the coat.
Suppliers differ, but many ask installers to avoid direct sun, very hot surfaces, and days when rain may arrive before the coat has set, and they give limits for surface temperature and humidity. Read the product data sheet and ask about application conditions before the start date. Some systems also go on better while the slab temperature is steady or falling rather than climbing, which is a matter of scheduling, not of squeezing every coat into a single day.
Reducing the chance of blisters coming back
| Step | Why it matters |
|---|---|
| Let the slab and screed dry and cure before waterproofing | Less vapour rises beneath the membrane |
| Clean away dust, laitance and loose material | Better bond and less lifting |
| Treat cracks and joints before the final coats | No openings for water or air |
| Use a primer suited to the surface and the system | Seals pores and helps adhesion |
| Respect coat thickness and drying time between coats | Solvent and water are not trapped under a dry skin |
| Avoid extreme heat, dew and rain risk | The membrane sets before it is stressed |
| Get the slopes and drains right | No standing water on the membrane |
| Flood test where suitable and re-inspect after the first summer | Problems surface while still small |
Some suppliers recommend vapour vents on certain bonded systems, depending on the roof design. Ask about it rather than assuming. Preparation is covered in more detail in how to prepare a roof for waterproofing.
Mistakes that make things worse
- Painting over the blister: coating it without opening it traps whatever is beneath and hides how it grows.
- Pricking it with a pin and walking away: some air escapes, water gets in, and the bond is not restored.
- Patching over damp: the swelling returns, it is only a matter of time.
- Rushing every coat into one day: it cuts the drying time the system needs.
- Mixing unrelated products: a new coat may not agree with the old one and can react or detach. Our list of common roof waterproofing mistakes covers more.
- Ignoring cracks and joints: water enters through them and vapour comes back up under the membrane. See concrete roof cracks and expansion joints.
- Relying on a thermal camera alone: it may show temperature differences but cannot reliably tell a wet pocket from a dry one.
What an inspection can and cannot show
An inspection usually combines a structured visual and tactile survey, a rough map of blister positions and sizes, a small opened sample where needed, a surface moisture check, and a review of details at laps and outlets. A flood test may be added where the roof allows it. These methods have limits: you cannot see beneath a membrane without opening it, a sample opening damages part of the system and must be resealed, and moisture readings shift with the weather. So we report findings together with how strong the evidence is, and do not promise a final fix before the cause is seen. If blisters sit near walls, drains or pipes, the roof leak details at parapets, drains and penetrations may also come into scope.
What drives the cost
We do not quote a figure before the inspection. The cost depends on the size of the affected area, whether the job is a patch or a redo, the existing system, the state of the concrete and its moisture, access to the roof, the number of details such as edges, outlets and laps, and whether drying or crack repair is required. To compare proposals fairly, ask for a written scope, as set out in our roof waterproofing quote comparison checklist.
What to send us
- The city (Jeddah or Makkah), the building type, and the membrane type if you know it.
- Wide and close-up photos of the blisters, with a coin or ruler beside one for scale.
- When the waterproofing was done, if known, and whether the blisters appeared in the first summer or later.
- Whether any dampness has shown inside, under the affected area.
- Whether people walk there, or AC units or tanks sit on that part of the roof.
We cover Jeddah and Makkah. See our pages on roof waterproofing in Jeddah and roof waterproofing in Makkah.
Frequently asked questions
Does a blister in roof waterproofing mean the roof is leaking?
Not necessarily at that moment, as the membrane may be intact above the pocket. But it is a weak point that can burst or crack and let water in. Inspect beneath it and check for dampness indoors before deciding what to do.
Should I prick the blister with a pin to let the air out?
It is not advised. A tiny hole does not restore the bond and can let water in. A better approach is to open the blister deliberately, dry the area, inspect the surface and then patch it with a compatible material.
Why did the blisters show up in summer?
Heat expands trapped air and turns trapped moisture into vapour, which pushes the membrane up and makes pockets visible. They often appear in the first summer after the work, especially where the base was not fully dry or the surface was poorly prepared.
Is a local patch always enough?
No. It can be enough when blisters are few, contained and sit over a dry base with an intact membrane. If they come back after repair, spread, or moisture is found beneath, the problem is in the base and the affected area usually needs to be redone.
Can I just apply another coat over a blistered membrane?
That is unwise. A new coat seals in what is under the blister and hides its growth, and it may lift with it. Open and inspect the area first, remove whatever is not bonded, and use a material compatible with the existing one.
How can I tell whether the concrete is damp under the membrane?
Taping a clear plastic sheet with sealed edges over bare concrete for a day gives a clue: droplets underneath or darker concrete suggest moisture rising. A concrete moisture meter may be used too, with readings interpreted per the supplier's guidance and the concrete type.
Do vapour vents prevent blisters?
On some bonded systems they may help, depending on the roof design and the supplier's instructions, but they do not replace a dry, clean, well-primed surface. Ask the supplier or the inspector what suits your roof before adding them.
Do you give a price before inspecting?
No. The cost depends on the affected area, the existing system, the state of the base and access, so we need to see the situation first. Send photos and the waterproofing date, and we will recommend the next step, with a quote after inspection.
Related pages
- Bashaer Al Khair: home
- Waterproofing services
- Preparing a roof for waterproofing
- Liquid membranes: pros and cons
- Foam vs rolls vs liquid
- Common waterproofing mistakes
- Ponding water and slope
- Flood test after waterproofing
- Repair or redo old waterproofing
- Concrete roof cracks and joints
- Roof waterproofing in Jeddah
- Roof waterproofing in Makkah