Skip to main content
Bashaer Al Khair — Water Leak Detection & Waterproofing
Active Service Coverage:Jeddah & Makkahالعربية
Bashaer Al Khair Waterproofing & Water Leak Detection
Bashaer Al KhairWaterproofing & Leak Detection

Pool Skimmer, Suction and Return Line Leaks: How to Check and Tell Them Apart

Quick answer: A skimmer leak usually shows up as a water level that drops to the skimmer opening and then stalls. A suction-side leak (before the pump) tends to show up as air bubbles in the strainer basket and a pump that loses its prime. A return-side leak (after the pump) gets worse while the pump runs and can soak the ground above the pipe. A simple first check is to compare your 24-hour water loss with the pump running against 24 hours with it off, allowing for evaporation. That points you in a direction; it does not pinpoint the leak. Locating it takes an on-site inspection.

Where the water travels, and why the route matters

Most residential pools run a closed loop. The skimmer draws in the surface layer with its leaves and dust. A suction pipe carries that water to the pump and its strainer basket. The pump pushes it through the filter, and a return pipe delivers it back through the return fittings. Some pools add a floor drain or a second suction point. The reason to learn this route is practical: the stretch before the pump runs below atmospheric pressure, the stretch after it runs under positive pressure, and a crack behaves differently in each.

water levelSkimmerReturn fittingPumpand strainer basketFilterSuction line: below atmospheric pressureReturn line: positive pressureSimplified sketch; every pool is plumbed a little differently
A simplified circulation loop: suction before the pump, pressure after it. Each side leaves different clues.

Because the pipes are buried under paving, concrete or soil, you almost never see the defect itself. You see its side effects: a level that keeps sinking, a damp or sunken patch, a noisy equipment pad, a top-up hose that never stays off. At this stage the goal is not to name the exact spot. It is to narrow the field so you know whether to look at the shell, the skimmer or the pipework.

Suction-side and return-side leaks behave differently

While the pump runs, a pinhole on the suction side lets air in rather than letting water out, because the pressure inside the pipe is lower than outside. When the pump stops, the same pipe sits under the pressure of the pool's own water column, so it can weep if the defect is below the waterline. On the return side the picture reverses: with the pump running, water is forced out of any gap, and with the pump stopped the leak usually slows a lot.

What you noticeLeans toward the suction sideLeans toward the return side
Air bubblesBubbles under the strainer lid, or streaming from return jetsNot typical on its own
Pump primeRepeated loss of prime, a louder pumpLess connected
Wet or sunken groundPossible, but often less obviousA damp or sagging strip along the pipe route while the pump runs
Loss with the pump runningMay be modest, since air enters instead of water leavingClearly higher than with the pump off
Flow at the jetsWeak or irregularWeak, or uneven between jets
After the pump stopsLevel may keep creeping down if the defect sits below the waterlineThe leak usually eases

Treat this table as a rule of thumb. Short runs, valves, manifolds and defects close to the waterline all blur the signals. Its best use is giving you the right words when you describe the problem to an inspector.

The pump on versus pump off loss check

This is a first-pass check, not a verdict. It works by isolating the effect of the pump. If the pool loses about the same amount either way, the shell, the skimmer or plain evaporation is more likely. If it loses clearly more with the pump running, think return pipework or equipment under pressure. Choose a calm stretch of weather and keep swimmers out.

  1. Disable any auto-fill. A float valve or automatic top-up hides the loss and ruins the measurement. If the pool has its own meter, note the reading.
  2. Set the starting level around the middle of the skimmer opening, stick a piece of tape on the tile or coping at the waterline, and photograph it with the time visible.
  3. Day 1, pump running on its normal cycle. After 24 hours, measure the gap between tape and water with a ruler. Call that loss A.
  4. Refill to the tape with a hose, then switch the pump off at its breaker and leave it off for 24 hours. Measure loss B.
  5. Compare A and B and write down the weather for both days, plus any splashing, backwashing or topping up.
Day 1: pump runningtape mark, read after 24 hoursloss = ADay 2: pump offrefill to the mark, read after 24 hoursloss = BCompareA clearly bigger than B:suspect the pressure sideA about equal to B:suspect shell, skimmer or heatSwitch the pump off if the water falls below the skimmer opening. Never run it dry.
The two-day comparison. A big gap between A and B points toward the pressure side; similar numbers point toward the shell, skimmer or evaporation.

Evaporation in the hot, dry, windy conditions that are common around Jeddah and Makkah can be considerable, and it hits both days alike, so it does not explain a gap between A and B. To separate evaporation from leakage you can add the bucket test for pool evaporation versus leakage, and the guide on pool water level drops: evaporation or leak goes further into the background.

Reading the result

ResultLikely meaningNext step
A clearly bigger than BReturn pipework or pressurised fittings are leakingInspect the equipment pad and the soil along the pipe route, and ask for a line test
A and B about the sameShell, skimmer, permanent fittings, or high evaporationWatch whether the level stops dropping at a particular height
Level stops at the skimmer openingThe problem is around the skimmer or the pipe beneath itInspect the skimmer surround and the movement joint beside it
Level stops at some other heightSomething sits at that height, such as a light niche, a step or a wall fittingRecord the height precisely and tell the inspector
Loss no bigger than weather explainsMostly evaporation, splash or backwashRepeat in different conditions before deciding
Safety notes before you test or inspect:
  • Electricity and water: pumps, lights and control panels run on mains power next to water. Never touch wet electrical equipment, and never do so while standing in water. Isolate the circuit at its breaker before opening a pump lid or a junction box. See water near electrical outlets: safety.
  • Do not run the pump dry: if the level falls below the skimmer opening, switch the pump off. Dry running overheats it and damages the seals.
  • Do not drain the pool on a hunch: emptying it can leave the shell exposed to groundwater pressure from outside, which may lift or crack it. Get advice first.
  • Do not pressure-test pipes with compressed air yourself: test plugs can blow out violently. Leave line testing to people with the right equipment.
  • Chemicals: never mix chlorine products with acids, keep them away from children, and ventilate the equipment room when you open filters or chemical feeders.

Skimmer leaks: the usual weak spots

A skimmer is a moulded box set into the pool wall with a pipe connection underneath. Its weak points are few and well known: the joint between the skimmer body and the pool wall, the movement joint between skimmer and surrounding deck, the pipe connection under the body, and the lid or basket frame. If the pool has an equalizer line it can be another source. Since the skimmer sits near the water surface, its leak often makes the level fall and then stop.

For cracks, joints and pipe penetrations in the shell more generally, see pool joint, pipe penetration and crack leak causes, and for the repair side read pool joint and fitting leaks: waterproofing.

Buried suction and return lines

You suspect the pipework when two or more signs line up: higher loss while the pump runs, a soggy, sunken or unusually green strip of ground along the route, trouble priming the pump, or a clear change in flow at the jets. An unexplained rise in the water bill can be a further hint.

Finding the faulty line usually means isolating each line with suitable plugs, pressure-testing it, and watching for a drop. Then comes locating the spot using listening gear, dye or, where the pipe allows, a small inspection camera. No single tool suits every pipe. Acoustic listening struggles on quiet plastic lines, and cameras cannot enter small bores or sharp bends. The page on the pressure test and what it can tell you covers its limits, and yard underground pipe leak signs and checks helps if the doubt extends to other pipework.

Check the equipment pad before blaming buried pipe

Walk the equipment area with a dry hand and a torch. Look for drips at the pump unions, a bead of water under the pump shaft seal, a multiport valve that is wet around its handle, and a strainer lid whose rubber ring is cracked or dry. Each of these either leaks or sucks in air, and each is far cheaper to fix than digging. If the pump cycles on and off or vibrates, read pump short cycling and pump room leaks.

What this test cannot settle

No single number for evaporation is right for every pool. It depends on temperature, wind, humidity, surface area, shade and whether a cover is used. Other losses are not leaks at all: splashing, backwashing, water carried out by swimmers, and overflow after rain. One day of measurement is therefore thin evidence. Repeat the comparison over two or three days under similar conditions. If doubt remains, an on-site inspection is the next step.

Decision table: what you see and what to do

ObservationLikely areaDo nowAsk for an inspection when
Level stalls at the skimmer openingAround the skimmerRecord the level, photograph the surroundThe level falls again after refilling
Constant bubbles in the strainer basketAir entering the suction sideCheck the lid ring and water levelThey persist after cleaning the basket and checking the ring
Damp strip over the pipe routeReturn line, most oftenSwitch the pump off and see whether it driesThe wetness persists or the ground settles
Same daily loss pump on or offShell, skimmer or evaporationRepeat and keep auto-fill offLoss exceeds what the weather explains
Water bill up with no other causeFrequent top-ups or a leakLog every refillIt stays high for two billing periods

Common mistakes

When to book an inspection, and what it involves

Book one if you see a persistent loss beyond what conditions explain, damp or sinking ground along the pipe route, a pump that keeps losing prime after the simple causes are ruled out, or visible cracking around the skimmer and coping. A visit typically starts with your history, photos and test numbers, then a look at the shell, skimmer and equipment pad, dye checks at suspect points, isolation and pressure testing of lines, and finally locating the spot with whichever method suits the pipe. We do not promise that one instrument will find every leak. Some cases need two methods, or a small opening once the spot is known. A tidy preparation list is in how to prepare for a leak detection visit.

It helps us if you send: photos of the pool, skimmer and equipment pad; both test results (A and B) with dates; whether auto-fill exists; and when you first noticed the loss.

Bashaer Al Khair covers Jeddah and Makkah. See pool leak detection in Jeddah and pool leak detection in Makkah, or browse all water leak detection services.

Frequently asked questions

How can I tell a skimmer leak from a pipe leak?

A skimmer leak often makes the level fall and then stop near the skimmer opening, with loose tiles or damp soil beside the skimmer, and similar loss whether the pump runs or not. Those are hints rather than proof. Dye testing and inspection confirm it.

Should I switch the pump off if I suspect a leak?

Yes in two cases: when the water falls below the skimmer opening, so it does not run dry, and when a damp patch grows over the pipe route during operation. The 24-hour pump-off step in the test above is also deliberate.

Do air bubbles in the strainer basket mean a leak?

They suggest air is entering on the suction side, perhaps through a worn lid ring, a loose union or low water. Often the cause is simple. Clean the basket, check the ring and the level before assuming a broken buried pipe.

How much does a pool lose to evaporation each day?

There is no single figure. It changes with heat, wind, surface area, shade and covers. Compare the pool with itself using a fixed mark over several days. A loss that does not respond to weather or pump state deserves a closer look.

Is the bucket test enough to find the leak?

It helps separate evaporation from leakage, but it cannot say where the water goes or tell shell from pipework. Pair it with the pump on versus off comparison to narrow things further.

Should I empty the pool before repairing a leak?

Not on your own. Full drainage can expose the shell to groundwater pressure from outside, which is a real risk where groundwater is high. A specialist should decide whether emptying is necessary and how to do it.

Can leak detection equipment pinpoint the leak every time?

No method suits every pool. We use visual checks, dye, line isolation, pressure testing and listening as the case requires, sometimes more than one, and we explain what each result can and cannot show before anything is opened.

What does a pool leak inspection cost?

We do not quote before seeing the case, because it depends on pool type, the number of lines, access and which methods are needed. Send photos and your test results and we will suggest the right next step.

Related pages

CallWhatsApp