Drinking Water Tank Waterproofing: What to Ask Before You Agree
A tank is one of the most sensitive parts of a building, because it stores the water that reaches the bathrooms and the kitchen. When it leaks, shows damp, or cracks, owners ask the same questions: should it be sealed inside or outside, with what material, and can it still be used for drinking afterwards? This page tries to answer the decision-related questions honestly and to show what to ask before you pay anything.
First: is the tank really the problem?
Before thinking about waterproofing, confirm that the loss or dampness comes from the tank itself. Several other causes look alike: a feed or outlet pipe connected to the tank, condensation on a cold tank wall, or roof leakage above a ground tank. A simple test helps: close the tank outlet and watch whether the water level falls with no consumption, noting the level at two times. If the level drops, the problem is in the tank or its connections; if it does not, the source is more likely in the pipework.
In underground tanks the opposite can happen: groundwater or rainwater can enter through cracks, so the water is contaminated from outside. This is among the most worrying cases because it does not show as a falling level but as a change in water quality, and it calls for technical inspection and water testing according to the relevant authority guidance.
Tank types and how the approach differs
| Tank type | Main risks | What to ask |
|---|---|---|
| Underground concrete tank | Cracks, loss outward or ingress inward, damp in walls | Crack treatment, a material suitable for drinking water, cover and openings |
| Rooftop tank | Sun and heat exposure, load on the roof, leaks at fittings | Sun protection, fitting checks and base condition |
| Plastic or fibreglass tank | Sun cracking, weakness at outlets | Often repair or replacement per manufacturer advice rather than an unsuitable coating |
| Old tank with flaking walls | Old layers peeling into the water | Remove the old coating completely before any treatment |
What "suitable for drinking water" means and how to check it
Many waterproofing products are designed for roofs or concrete structures and are not suitable for direct contact with drinking water. Some products are made in formulations for that contact and come with documents from the manufacturer or an approval body. We will not name a specific standard or product here, because the correct reference is the competent authority in the Kingdom and the product documents themselves.
So ask for the following in writing before work starts: the exact product name, its technical data sheet, evidence of suitability for drinking water, the manufacturer instructions, and the curing time before the tank is filled. If the contractor will not provide these documents, treat that as a warning sign.
Typical stages of the work
- Empty the tank, isolate the supply, stop the pumps and disconnect their power.
- Clean walls and floor, removing algae, deposits and flaking layers.
- Inspect cracks, joints, pipe penetrations and the cover, and decide what needs repair.
- Repair cracks and joints with suitable materials, drying or conditioning as the product requires.
- Apply the chosen coating at the recommended thickness and number of coats.
- Allow full curing and ventilation before any filling.
- Wash and disinfect the tank following approved drinking water guidance, then fill and monitor.
Internal or external treatment?
Internal treatment stops water passing from the tank into its walls, while external treatment protects against outside water or heat. For underground tanks both sides matter, because water can move in either direction. The decision depends on where the crack is and whether the outside is reachable. What we do not recommend is coating a wet or saturated surface with a product that cannot tolerate it, because it detaches over time and leaves flakes in the water.
Common leak locations in tanks
| Location | Sign | What to check |
|---|---|---|
| Inlet or outlet joint | Damp around the pipe at the tank | Joint seals and pipe support |
| Wall-to-floor junction | Damp at the base of the outer wall | Corner cracks and the sealing there |
| Cover and access hatch | Dust or rainwater getting in | Cover fit and edges |
| Wall against soil | Stains, damp or greener grass in one spot | Loss outward or ingress from outside |
| Tank floor | Level falls with no use | Inspect the floor after emptying |
Common mistakes
- Using a roof coating inside a drinking water tank.
- Not removing the old flaking layer before coating.
- Rushing to refill before the curing period ends.
- Forgetting to wash and disinfect after the work.
- Neglecting the cover and vents, the route for dust and insects.
- Ignoring an unusual smell or taste after the work.
Signs that call for re-inspection after the work
If after using the tank you notice a change in taste or smell, flakes in filters or in the water, new damp on the outer wall, or an unexplained fall in level, stop drinking from it and ask for an inspection. These signs may mean a cracked coating, incomplete curing or a problem at the joints, and they should not be ignored. If the tank supplies a building with children, elderly people or patients, be stricter about documents and about washing and disinfection periods, and consult the water authority where needed.
Scenarios by building type
Villa with an underground tank and a roof tank
In villas the underground tank is the largest and hardest to reach, while the roof tank is the one exposed to sun. Each may need a different treatment, and alternative water must be arranged during the stoppage. Plan the work so the home is without water for as short a time as possible, remembering that curing and washing time must not be shortened.
Apartment block with shared tanks
A shared tank is the responsibility of several households, so coordinate with the owners association or manager, tell residents the stoppage date in advance, and agree who bears the cost and who signs the documents. A delay in washing and disinfection affects everyone, so request documents in writing and keep a copy.
Old tank not inspected for years
Old tanks usually have deposits, perhaps earlier flaking layers, and many small cracks. It is better to start with inspection and cleaning before the final estimate, because much of the cost and time is set by the condition of the surface after cleaning.
What to do while the tank is out of service
- Store enough drinking and cooking water from another suitable source.
- Tell household members or residents the date and expected duration.
- Switch off water-dependent appliances so they do not run dry.
- Make sure the pump is not run without water, as it can be damaged.
- Keep copies of the product documents and of the washing and disinfection record.
What affects the cost
We do not quote prices because cost depends on tank size, position and type, the condition of walls and floor, the number of cracks, the material required, ease of emptying and access, washing and disinfection, and whether supply must be stopped for a set time with a substitute source. Send photos of the tank inside and outside with a description of the problem and we will arrange an inspection to establish what is needed.
Questions to ask any company before agreeing
- What is the exact product name, and where is its drinking water suitability document?
- What are the manufacturer instructions for surface preparation, coats and curing time?
- What are the safety and ventilation arrangements inside the tank?
- How will cracks, joints, cover and openings be treated?
- How will washing and disinfection be done, and under which approved guidance?
- What does any written warranty cover and exclude?
Routine checks that extend tank life
Even after treatment, a periodic visual check of the tank from outside is wise, along with a look at the cover and strainers and attention to any change in colour, taste or smell. Tanks should be cleaned and washed regularly according to use and the guidance of the competent authority, and each maintenance job recorded with its date. That way a problem is found early, before it grows.
How we handle tanks
We first check whether the tank is really the source of the problem or whether another leak is involved, then assess its condition and decide on a suitable treatment. We do not promise an absolute result, and we do not say our material is approved for drinking water unless the documents exist and you can read them. If the tank needs replacing or repairing in a different way, we will say so plainly.
Frequently asked questions
Is any waterproofing product suitable for a drinking water tank?
No. Many products are not intended for contact with drinking water. Ask for a document from the manufacturer or an approved body proving suitability before work starts.
Can a tank be waterproofed while full?
It is normally emptied, cleaned and dried as the product requires, and coating a wet surface with a product that cannot tolerate moisture is not advised.
How long before I can use the tank again?
It follows the manufacturer curing time, then washing and disinfection. We do not promise a duration before inspection and knowing the product.
How do I tell a tank leak from a pipe leak?
Close the outlet and record the level over time. A fall with no use points to the tank or its fittings.
Should plastic tanks be coated?
Usually follow the tank manufacturer advice. Repair or replacement may suit better than an unsuitable coating.
What if the water tastes different afterwards?
Stop drinking it and ask for an inspection; it may need rewashing, further curing or a review of the product.
Do you cover Jeddah and Makkah?
The site presents tank waterproofing in Jeddah and Makkah. Send tank photos on WhatsApp to confirm details.
Contact us
To discuss your case in Jeddah or Makkah, call us or send photos on WhatsApp.